DOF Tutorial

i posted this tutorial before pa sa 3dpinoy, and i think its time to share it again here... this is for sir guru nomeradona, who never stops teaching us newbies... here it is... for old version of vfsu....



1. use the tape measure (T) to get the distance of the 1st point of camera
2. upto the 2nd point of object view of desire.
3. for my personal preference, i always change my unit of measurement to imperial (feet/inches), as for all we know, sketchup default DOF perimeter should be in inches...convert the indicated value (6'-1/8") to inches (approx. 72")
4. open up the vray options and expand the camera parameters and tick (on) the Depth Of Field category, they gave a fine default settings on aperture, center bias, aperture and subdivs... but if you want to get a more blurry effect, increase the aperture from 0.1 upto desired value (hope i'm correct, give me additional info bout DOF blurryness.. hehehe...) you can also increase the subdivs there (i have a slow pc that time thats why 8 was enough for me), uncheck the override focal distance then input the value you've computed awhile ago ( i used 70" just to give it a whole numerical value, 2" is not far from your object, its ok...) then hit RENDER!!

DOF OUTPUT

good job erick

nomeradona wrote:good job erick

thanks ser nomer... maling section ata nalagyan ko nito... paki-move nalang po ser under vray sketchup tips and tricks...

wow! galing. ayus ung pag kaka focus.

thnx for the info sir!

wheay wrote:wow! galing. ayus ung pag kaka focus.

thanks po ser wheay

jenaro wrote:thnx for the info sir!

you're very much welcome ser jenaro

bro meron nga palang mga ruby to know exactly yung location distance ng camera. alam ko galing kay rick wilson.. nasa smustard.com .. libre

nomeradona wrote:bro meron nga palang mga ruby to know exactly yung location distance ng camera. alam ko galing kay rick wilson.. nasa smustard.com .. libre

speaking of ruby ser... post naman tutorial... me nakuha kase ako ruby ng su pero di ko alam gamitin hehehe...

ERICK wrote:i posted this tutorial before pa sa 3dpinoy, and i think its time to share it again here... this is for sir guru nomeradona, who never stops teaching us newbies... here it is... for old version of vfsu....



1. use the tape measure (T) to get the distance of the 1st point of camera
2. upto the 2nd point of object view of desire.
3. for my personal preference, i always change my unit of measurement to imperial (feet/inches), as for all we know, sketchup default DOF perimeter should be in inches...convert the indicated value (6'-1/8") to inches (approx. 72")
4. open up the vray options and expand the camera parameters and tick (on) the Depth Of Field category, they gave a fine default settings on aperture, center bias, aperture and subdivs... but if you want to get a more blurry effect, increase the aperture from 0.1 upto desired value (hope i'm correct, give me additional info bout DOF blurryness.. hehehe...) you can also increase the subdivs there (i have a slow pc that time thats why 8 was enough for me), uncheck the override focal distance then input the value you've computed awhile ago ( i used 70" just to give it a whole numerical value, 2" is not far from your object, its ok...) then hit RENDER!!

DOF OUTPUT

NICE TUTORIAL ERICK-thanks. dati ko pa gustong i-try gawin itong DOF, but di ko na-gets yung nasa manual ng VR.

very much thank you sir archfsm

hehe, hanep to sir rick, kelangan ko matutunan to d ko pa to lam e, thanks agen!

salamat po sa tut na ito!!

m | 9 z wrote:hehe, hanep to sir rick, kelangan ko matutunan to d ko pa to lam e, thanks agen!

no problem po... basta makatulong... thanks

ortzak wrote:salamat po sa tut na ito!!

thank you so much sir ortzak